HOW TO REMOVE AND ALSO REPLACE A BATH TUB

How to Remove and Also Replace a Bath Tub

How to Remove and Also Replace a Bath Tub

Blog Article

This Page

How do you feel in regards to Tools You Need to Install a New Bathtub ?


How to Install a Bathtub Yourself
Mounting a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your shower room if you have currently gotten a new tub and do not require to alter the plan of your previous supply of water pipes.
Your devices and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be rather bothersome because of the restricted accessibility that is commonly the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
    Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, position the faucet in the placing opening in the bath/basin making certain that the washers are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Setting up the Bath tub


    Making use of both wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
    The following objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads level.
    To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
    Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
    Ultimately, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has been made use of a minimum of once as this will certainly resolve it into its final position.

    Preparing for the Installment


    To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to prevent pressure on the tub.
    Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.

    Tiling Around the Tub


    In the location where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
    You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I was made aware of that report about How to Install a Bathtub Yourself through an acquaintance on a different web address. Sharing is good. Who knows, you may just be helping someone out. Kudos for your time. Visit us again soon.




    Request Free Estimate


    Report this page